"Where Fillmore County News Comes First"
Friday, May 22nd, 2015
Volume ∞ Issue ∞
- 12:15:00, May 20th 2015 - Shorty - Makes me feel pretty old when I read about people I knew. I would like to ... [Read More]
- 11:34:36, May 20th 2015 - SV80 - To Future: I can empathize with your regarding Hawkeye63. He exhibits all t ... [Read More]
- 12:49:06, May 19th 2015 - future - @Hawkeye63 My entire argument has been based on legal civil rights argument ... [Read More]
- 7:22:50, May 19th 2015 - hawkeye63 - There you have it fellow citizens, I sure hope America is paying attentio ... [Read More]
- 6:06:44, May 18th 2015 - Redhorse51 - Thank you for a great read. Like an addicting mini-series, I could not ... [Read More]
- 7:26:03, May 17th 2015 - future - @Hawkeye63 I'm going to address your post per sentence to make it clearer ... [Read More]
- 2:11:36, May 17th 2015 - Hawkeye63 - So in a nutshell you are fine with forcing conservative, traditional Chri ... [Read More]
- 9:45:42, May 17th 2015 - Paul - The question I have about the belief that some should not have to serve same s ... [Read More]
- 6:43:06, May 17th 2015 - Crack some heads - This is a really good article, unfortunately a lot of people can't ... [Read More]
- 9:38:48, May 16th 2015 - email@example.com - Thank you for providing this good article on distracted driving. ... [Read More]
Fri, Oct 8th, 2010
Posted in Agriculture
Posted in Agriculture
Last Thursday, while watching the rain, the thoughts of an early easy harvest came to an end. I came across some information prepared by Crops Regional Educator Jodi DeJong-Hughes and Extension Agronomist Jeff Coulter in 2009. They addressed options for tillage in wet soils.
Soil compaction and smearing is a distinct concern when pulling implements through or driving on wet soil. Residue management is another concern. We want the fields to dry out quickly next spring for quick planting. To limit soil damage and to help with soil warm-up in the spring, keep these strategies in mind: fill in ruts, keep tillage shallow, properly prepare equipment, and plan ahead for spring.
If you have ruts in the field from fall harvest, the first instinct is to aggressively fill them in. Soil structure is your soil's number one defense against future soil compaction, and tillage destroys structure. To maintain the structure your soil has, just fill in the ruts with light tillage by running equipment at an angle. You may need two to three passes to accomplish this. These areas will not yield as well as the non-rutted area, but there is not much you can do to change this.
A light tillage pass like disking is useful for incorporating residue and introducing air into the soil. If the soil is wet, try to operate this shallow tillage equipment no deeper than three inches. Another option for wet soils is vertical tillage. Vertical tillage runs one to three inches deep and uses straight or wavy coulters, a harrow, and rolling baskets. Vertical tillage fluffs-up the remaining residue with shallow penetration and minimal inversion of the soil.
Lifting wet soils can create clods. If using a chisel plow or disk ripper, shallow up the shanks, and use narrow points. The wings have a higher potential for smearing the soil. Twisted or parabolic shanks will create the most soil movement and can create soil clods. Clods in themselves are not bad going into winter. Next spring they will leave more surface area for water infiltration. However, a field with clods will likely need an extra tillage pass in the spring to create an adequate seedbed for good seed-to-soil contact.
Wet soils have a high potential for soil compaction. To limit soil compaction, keep axle loads under 10 tons and properly maintain air pressure in the tires. Not only does this help the soil, but it will help your tractor run more efficiently and with less slippage. On wet soils, use the lightest tractor that can still get the job done.
There isn't much you can do to reduce the weight of combines. If possible, unload before the grain hopper is full to limit axle loads. Large grain carts have very high axle loads (up to 43 tons per axle). Control the wheel traffic from grain carts by running in the previous combine tracks and don't cross the field at a diagonal. Eighty percent of the compaction happens on the first pass; use it to your advantage.
Check over equipment and replace worn parts, sharpen blades, and adjust down pressure for each field's soil conditions. These small details are more important in extreme moisture conditions.
Planting soybeans may be the best option in fields with heavy residue. They are very adaptive to higher residue levels, are not as soil temperature sensitive as corn, and grow well in no-till situations. If trying no-till beans, set the corn header of the combine as high as possible to reduce the amount of residue matted onto the soil surface.
Corn on corn has more residue to manage and needs additional nitrogen fertilizer than corn following soybean. Row cleaners are a must for corn following corn in order to obtain uniform seeding depth and facilitate warming of the soil over the seed. For corn following corn where high quantities of surface residue are present, consider a starter fertilizer.
This will be a challenging fall harvest. Keep your options open as things can change quickly.